Rockboard MOD 3 V2 TRS & XLR Patch Bay

All-in-One Patchbay voor pedalboards

Geschikt voor MOD-slots in RockBoard pedalboards
Compatibel met een breed scala aan andere pedalboards
Fungeert als centraal toegangspunt tot de effect-setup
Legt duidelijke kabeltrajecten vast naar en van het pedalboard
Afneembaar frontpaneel voor montage op of onder pedalboards
3x 6,3 mm TRS thru
2x XLR thru (male voor / female achter)
1x XLR thru (female voor / male achter)
1x DC 2,1 x 5,5 mm holle stekker thru
1x AC IEC door (male voor / female achter)
Alle aansluitingen gespiegeld aan de achterzijde
Afmetingen met frontpaneel (B x D x H): 175 x 85 x 47 mm
Afmetingen zonder frontpaneel (B x D x H): 160 x 85 x 33 mm
Gewicht: 450 g
Incl. montageschroeven, borgmoeren en TX-sleutel

Opmerking: Registreer uw product op www.w-distribution.de/Warranty en verleng de garantie tot 4 jaar

Let op! Registreer uw aankoop op shop.warwick.de/en/warranty-registration voor een verlengde garantie van 4 jaar.

30 dagen Money-back garantie

Leverbaar sinds Augustus 2019

artikelnummer 468599

verkoopseenheid 1 stuk

€ 69

Alle prijzen incl. btw

Best seller rang

in accessoires voor rockbag

Practical patchbay module

The RockBoard MOD 3 V2 is a practical patchbay module for acoustic guitarists and vocalists, which consolidates all the necessary connections of a pedalboard in one central access point, thus shortening cable paths and providing users with a better overview of their entire effects setup. The MOD 3 V2 is equipped with an XLR input and two XLR outputs to provide a multitude of options for balanced audio signals, including a vocal setup with stereo effects. The module also comes with three jack connections as well as a DC and an AC IEC mains connection for delivering power to the multi-power supply under the board.

Flexible routing options

The jack connections (A-C) and XLR connections (1-3) on the RockBoard MOD 3 V2 are wired from the front to the rear of the module courtesy of the pass-through design, thus allowing various configurations. Vocalists can connect any microphone to the XLR input and use the XLR outputs to send the stereo signal from an effects processor on their pedalboard to a mixing console. Acoustic guitarists have the option of attaching a DI box to their pedalboard or even integrating delay and reverb effects into the effects loop of their acoustic amplifier.

For acoustic musicians and vocalists

The RockBoard MOD 3 V2 is the perfect enhancement for any pedalboard. As a flexible patchbay for TRS, XLR, DC, and AC IEC connections, it enables all connections to be organised in one convenient module and provides clearer and neater cable routes to the exterior of the pedalboard. The MOD 3 V2 is the ideal solution for vocalists looking to transmit a balanced stereo audio signal from their effects setup to a mixing console, but also for acoustic guitarists who use a DI box or rely on an acoustic amplifier for their performance. Both DC and AC IEC mains connections add the perfect finishing touches to the patchbay concept.

RockBoard MOD 3 V2 patchbay for pedalboards

About RockBoard

RockBoard is a brand belonging to Warwick Music Distribution GmbH, which is based in Markneukirchen in Germany's Vogtland region. RockBoard's range focuses on pedalboards, which are available in numerous different designs to suit any application and budget, and are complemented by an extensive range of pedalboard accessories, from slick patchbays for expanding the boards and high-quality patch cables for loss-free connection through to high-performance power adapters and the "QuickMount system" for rapid effect changes. In short, RockBoard offers virtually everything that players need to easily set up their own individual pedalboard.

For mounting in MOD slots

Users of RockBoard pedalboards from the TRES, QUAD, and CINQUE series will ideally mount the MOD 3 V2 in the dedicated MOD slot, which is built into the front of the board and ensures a secure means of attachment. Alternatively, the front panel can be removed, allowing the module to be mounted on or underneath pedalboards using self-adhesive hook and loop tape. A robust MOD rack is also available from the manufacturer as an optional extra, which allows the module to be used with pedalboards from alternative providers and can be adjusted to accommodate different mounting directions and positions according to the design of the pedalboard.

Dit is wat klanten die dit product bekeken hebben gekocht hebben

Rockboard MOD 1 V2 TRS & XLR Patchbay

Rockboard Pedalboard Tape 100 cm

€ 14,90

kochten

Harley Benton Pedalboard Organizer Kit

€ 4,90

35 Klantenbeoordelingen

5 25 Klanten 4 5 Klanten 3 3 Klanten 2 1 Klant 1 1 Klant

4.5 / 5

afwerking

Review richtlijnen

26 Recensies

Vertaling tonen

Origineel tonen

Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.

Total disappointment

TsalerA 30.08.2021

This is the reason of my bad evening.
Bought it to use with Rockboard pedalboard + Rockboard PSU. Looks cool, but that's all.
1. You have to do an screw-thread in the native pedalboard fof this thing by youself! Guys at the factory were very busy)) DIY!!!
2. It's patch-bay for the XLRs! Guess what?) XLR plugs do not fit in to the pedalboard holes!
3. Connected this thing to the native RB PSU. And it's very very noisy! Spend an hour looking whats the problem. It's this thing!!! Unpluged PSU fron this thing. connected PSU bypassing this thing, and it become less noisey!

Summary: This thing is patch-bay for xlrs, jacks and power.
You can not use this with XLRs and Rockboard pedalbords. You Can not use this with Rockboard PSU. This thing is useless. Waste of money(

Evaluatie melden

Bent u van mening dat deze evaluatie om een of andere reden onjuist of onacceptabel is? Geef ons s.v.p. de reden voor uw bewering in de volgende tekstbox en – indien mogelijk – uw E-mailadres voor verdere vragen.

Vertaling tonen

Origineel tonen

Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.

Can't imagine using my Rockboard without it

AleksanderS 15.02.2025

Been using it in my Rockboard 4.2 for over 2 years now. I have a BOSS RC-600 looper on my board along with 11 other pedals, and it makes everything very convenient and tidy. No added noises to the system, no complaints about build quality. Bought an XLR reverser adapter cable so I can connect 2 mics to it, two of the 1/4" outputs are routed as L & R mono outputs from RC-600, and the third jack output is for Stereo Headphone Out, very convenient. 3x 1/4" TRS outputs can be turned into 6x mono in-outs using Y-splitter cables, which is great versatility. The added 9V output great for powering any extra pedals that are not permanently on my board that I might be using or trying out. It saves a lot of time and mess - no fiddling about with cabling, going under the board to connect or route something - just plug what you need in the MOD 3 patch-bay, connect the power cable, and everything works.

Evaluatie melden

Vertaling tonen

Origineel tonen

Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.

I love it!

Love Rockboard 02.06.2021

Makes my board a lot neater and it looks cool too! Perfect for singer/guitarists (like me) or anyone that needs a few xlr ports on top of the normal jacks.

Evaluatie melden

Vertaling tonen

Origineel tonen

Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.

Extremely useful passive connections

Cian M. 23.12.2023

Needed this for a pedalboard build a few years back and have used it in a few different routing / signal chains since then.
The other rockboard patchbays look great too but this has the perfect connections for me. The Jack's being TRS for stereo or midi control is great. Makes routing a board with midi controls/foot controller so much neater and easier.
It is also nice for putting my amp foot switch, guitar signal and vocal mic outputs all within a few centimetres. Max setting up at the gig feel like no work at all.

Evaluatie melden

Alle waarderingen lezen

Rockboard MOD 3 V2 TRS & XLR Patch Bay

All-in-One Patchbay voor pedalboards